which string?

[quiverfull]

#5159

I just obtained a Damon Howett Hunter, 60# @28″, 62″ AMO. This is an old bow, not the new Martin version, so I need to use B50, and I prefer endless loop. I want to get a couple of high quality strings for it. I think I will need 16 strand for that draw weight, even though my 27″ draw will drop it 3# or so.

Any recommendations on good strings? Thanks, JB

[quiverfull]

#40960

I got the Howatt bow today (:D) , again AMO 62″, 60# at 28″.

I also ordered and received an endless loop B50 string supposedly for a 62″ recurve, but it leaves me at a brace height of about 6 1/2 inches, which does not seem like enough.

Any suggestions? JB

[Bruce Smithhammer]

#40989

I would agree that 6-1/2″ is too low for that bow. You’re probably going to want a brace height somewhere around 7-1/2″ to 8″ for a Hunter. You can twist the string to shorten it, thereby increasing the brace height. However, in my experience, endless loop strings don’t have the range of adjustability that Flemish twist strings have.

[quiverfull]

#41108

Smithhammer, you think a 56″ string would do it? The one I got measures 58 1/2″. I generally prefer endless loop strings, perhaps because that is what I’m used to. Can certainly get a Flemish twist if that would be best. Thanks for your reply..JB

PS: is there any provision for different size (diameter) Flemish strings, or does one size fit all draw weights?

[Charles Ek]

#41159

I prefer Flemish twist strings for the adjustability. In B50, you’ll usually see a recommendation to use 16 strands for that bow weight. The number of strands can safely vary downward with less weight (and goes up with weight), or with the stronger bowstring materials used on newer bows.

I’ve bought several strings from this guy with success (be patient for delivery). He is familiar with the needs of older bows: Flemishstrings.com

[Bruce Smithhammer]

#41233

Generally, the string should be 4″ less than the AMO length for a recurve, and 3″ less for a longbow. But that’s just a guideline. Have you tried twisting the endless loop string a bit to tighten it up?

Keep in mind you’re going to get some stretch with B50 as well, as it breaks in. Given the limited adjustability of endless loop strings in general, it sounds like that string may be a little too long for your bow. But of course, this is just internet armchair advice, without being able to see anything we’re talking about.

[Ralph]

#41278

X2 on what the Hammer speaks!:D

Hope you enjoy the new bow!!:D

[Jason Wesbrock]

#41300

Endless strings are just fine. You can twist them up or down just like a Flemish. To be honest, I’ve found endless strings a lot more stable and less prone to creep, but that’s just me. It seems most everyone I know with a Flemish string is constantly messing with it to keep their brace height correct.

With respect to your bow, you’re probably going to want that brace height over 8″ with a Dacron string. Closer to 8 1/2″ is my guess. The string you got is too long, and the amount of twisting needed to get your brace height up 2″ is far more than you’d want in there. I’d get a new string an inch shorter than the one you have. It should put you in the ballpark, and you can twist it slightly from there.

[quiverfull]

#41499

I am going to a local archery shop tomorrow and try a few strings. Also, ordered a couple of Flemish twist strings from bearbowman. thanks for the referral, eidsvolling. I will just try a few and see what works. Thanks for all the help…JB

[Bruce Smithhammer]

#42112

J.Wesbrock wrote: Endless strings are just fine. You can twist them up or down just like a Flemish. To be honest, I’ve found endless strings a lot more stable and less prone to creep, but that’s just me. It seems most everyone I know with a Flemish string is constantly messing with it to keep their brace height correct.

I would definitely agree with the first part of your comment, Jason – in my experience, endless loop strings are less prone to creep when the string is new. But once broken in, I don’t have any issues with my Flemish strings continuing to stretch or needing to be messed with – after the initial stretch, they don’t creep at all. Both types of strings work great, but it does seem like you have less adjustability with an endless loop to begin with, which isn’t to suggest that they aren’t ‘fine’ strings, it’s just something to be aware for the archer who is unfamiliar with them.

[quiverfull]

#42611

I picked up a 56″ Flemish twist today, which braced me at 7.75″. I have taken a few shots prior to formally tuning, and wow! That thing hits with authority! Very smooth draw. It’s the heaviest draw weight bow I have ever owned (by 4#),but I was able to get off a dozen pretty well done shots before starting to feel it in my shoulder. Since that shoulder turns 60 in July, I think I’ll back off and take it slowly.

I was sorry to see that Alaska Bowhunting is discontinuing their Superglove. It’s my favorite, and I managed to pick a spare size M. Now I’m rambling; good evening, all…JB

[wahoo]

#43388

listen to what J said. I twist my own strings and don’t have probs with b50 flemish twist. Your bow would like that 8 1/2 brace. Love those Howatts.

[Author]

Posts